Reflux Still for Distillation: AlcoEngine

For enthusiasts wanting to make clean pure neutral distilled water, perfumes, essential oils or spirit.

The whole system is designed to save, time, money and parts, and fit in one box for easier storage and cheaper shipping.

With its easy-to-use operation, amazing features, and rock-solid reliability. It is simple, easy and fun to use.

Note: Brewzilla units you will need to purchase the dome lids.  This is sold separately and is not included with the Robobrew unit.  The stock glass lid that comes with the Robobrew unit will not be suitable.

No more stuffing around with water flow speed!

Some stills are hard to operate and require fine-tuning of the water flow in the condenser.  These stills include the t500 and other coolant management or (CM) designs.  This means that you have to constantly adjust the flow of water/coolant to get consistent results.  This can be also an issue if you are using a pressure pump that cycles on and off in your house or it can even be an issue if you flush the toilet and momentarily the pressure in your hose feeding the still drops.  This still on the other hand is an FM design that controls the flow of spirit directly.  So the as long as you have enough coolant it doesn’t matter how fast your coolant flows through the still.  This makes the still far easier to operate than many other brands like the t500.  The purity of the distilate can be controlled by two included flow control inserts that are shown in the attached photos.  These brass inserts come with a 1.0mm hole and a 0.6mm hole.  As the hole gets smaller you the speed at which the spirit comes out of the still will decrease and this will, in turn, increase your reflux ratio and therefore give you higher purity.  This makes this still design Extremely easy to use as you just open up the ball valve and let the flow control insert of your choice do the job.

Typically the 1.0mm insert is good for stripping runs and then on the final cut, you can use the 0.6mm insert.  Alternatively, you can use the ball valve to control the spirit flow too but this is a sensitive adjustment and required a bit more skill for this type of manual adjustment so we recommend you just use the brass inserts that come included.

Easiest Still to Use – That’s our guarantee

This bulletproof design is so easy to use that we are giving you a guarantee that you will get a great distillation experience in no time flat.  All you need to do is make sure you have adequate water/coolant flowing through the head and just about everything else will look after itself.

Compatible with Many Boilers

This still design is compatible with many boiler types.  One option is just to get a pot and drill a 47mm hole in the lid and this still will fit no worries.  The still also fits many standard boilers such as the standard Turbo Boilers, Robobrew, Grainfather, etc. This still can also fit the top of stainless steel kegs too.  So you can easily make your own keg boiler.  You can use a 2inch tri-clover clamp (not included) and then use the clamp to attach this still to the top of a 50L keg.  So you will not find a more compatible still design that fits a wide range of boiler types.  This can do it all.

Made from Solid Copper

Unlike stainless steel stills and stills that are only copper plated, this still is made from solid copper.  When your hot spirit comes in contact with copper the copper acts as a catalytic converter and drives sulfur out of the spirit.  This process means you get fewer “off-flavors” and you simply get the better quality distillation.  Copper is an expensive metal now and it definitely increases the cost of the still manufacture but we can say for sure that there is a very good reason why it’s still the preferred material by many serious distillers simply because the results are superior.  Don’t listen to other people tell you that stainless is the best.  There is no substitute for copper and a still like this will last you a lifetime.

Simple Assembly and setup

This still is mostly assembled but you still have to connect your garden hose and coolant supply. You can just use your garden hose but it’s a bit of a waste of tap water so we recommend that you get a tank at least 500liters in size then use a powerful recirculation pump to drive the still.  We would recommend one of the desert air cooler pumps or any other suitable high-pressure pumps you can purchase separately yourself.  Flow rate is not as important as a high head pressure/maximum pressure capability. When you get the still you just need some Teflon tape and just attach the fittings as shown in the photos above in this ad.  Please make sure you connect all the fittings and check for leaks before you start distilling.  There is nothing worse than trying to attach a fitting once the still has heated up.

Features

• Lead-free brass
• Lead-free silver soldering
• High-quality manufacture
• Super easy to use and will yield results in very high-purity distillate